AN6884 DATASHEET PDF

AN datasheet, AN circuit, AN data sheet: PANASONIC – 5-Dot LED Driver Circuit,alldatasheet, datasheet, Datasheet search site for Electronic. AN datasheet, AN pdf, AN data sheet, datasheet, data sheet, pdf, Panasonic, 5-Dot LED Driver Circuit. Description, 5-dot Led Driver Circuit. Company, Panasonic Industrial Company/ Electronic Components. Datasheet, Download AN datasheet. Cross ref.

Author: Goltigrel Shakticage
Country: Syria
Language: English (Spanish)
Genre: Software
Published (Last): 1 March 2017
Pages: 445
PDF File Size: 9.20 Mb
ePub File Size: 7.25 Mb
ISBN: 669-3-49492-819-4
Downloads: 10216
Price: Free* [*Free Regsitration Required]
Uploader: Vudotaxe

The LED pins connect to the negative side of the LEDs, and the pins go low when the output of the internal amp goes above Vref dropped by voltage dividing resistors at each comparator. Right, I get that pin 7 is the output of the amp, but it’s part of the negative datasheeh loop on the amp.

Fadecomic 2 6.

It just shortens the range of turn over which the potentiometer works. As displayed, the LEDs go from fully off to fully on over roughly the entire turn range of the potentiometer. Vref is the high side of the 5 LED comparators in the datasheet block diagram.

Email Required, but never shown. By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. That is to say that the LEDs all come on at a much smaller turn of the potentiometer. Indeed, it must in order for any of the LEDs to turn on! Reverse biased capacitor on IC input pin Ask Question. Sign up using Email and Password. Pin 8 accepts a positive input voltage.

Placing it at a higher voltage within the datasheet’s max specified V will both lower the amplification and raise the lower rail of the aj6884 in the block diagram.

  DENTRO LA GLOBALIZZAZIONE BAUMAN PDF

Post as a guest Name. Sign up or log in Sign up using Google.

(Datasheet) AN pdf – 5-Dot LED Driver Circuit (1-page)

The diode will mess up the response of the chip due to its forward voltage drop. Pin 7 is the output of the internal amplifier, and pin 8 is its input, designed to accept a low-level AC input 57 mV for a 0-dB indication. You might want to edit to explain your answer a bit more.

I’m not following you. It’s the DC bias determine the polarity. I’m not reading it that way.

AN 데이터시트(PDF) – Panasonic Semiconductor

Capacitor with polarity can be used ac couple or blocking. There’s still a much shorter datasueet over which a varying number of LEDs come on.

It appears to be reversed. That’s clear, because the input in my test circuit is DC.

(PDF) AN6884 Datasheet download

Most people use “low” to refer to either a lower voltage, or a lower position on the diagram. So it determines the DC bias of the block capacitor’s polarity.

Very confusing terminology, since the inverting input can have a higher voltage than the noninverting input. Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies. I know the correct names, but I conversely find “inverting” and “noninverting” confusing when dealing with comparators, since those terms make more sense when dealing with op-amps.

It sounds like you’re trying to drive this circuit with a signal that includes a considerable DC bias, which explains why all of the LEDs light up right away when you remove short out the capacitor.

However, if that’s the case, I can’t explain why reversing the capacitor doesn’t work, unless the actual polarity of the capacitor is backwards from what you think it is. Have you tried a non-polarized capacitor e.

  LYNNE GRAHAM TEMPESTUOUS REUNION PDF

By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies. Per AN’d datasheetPin 8 is the signal input pin, and it’s the internal Op amp’s positive input. Passing Vin through a reverse capacitor seems to be potentially more prone to failure.

By “low side”, you’re referring to the inverting inputs of the comparators. Per AN’d datasheet.

Home Questions Tags Users Unanswered. If I “correct” the orientation, the circuit does not work at all.

AN6884 Datasheet PDF

There is also no discharge path with your arrangement. This circuit will light the LEDs as the input voltage on pin 8 increases relative to pin 7. I am looking at the test circuits on the data sheet for the AN VU meter IC, and I cannot understand the connection to pin 8 in the following diagram: How does doing datashdet to pin 7 or pin 8 affect that?

Can someone explain what the reversed capacitor is doing here? That means there is a small current flow out from the pin. If Datasehet remove the ratasheet. Setting 7 higher than ground biases the low side of the comparators, allowing them to turn on with a lower output from the amp. You should fix the capitalisation of sentences and electrical units ‘F’ for farad to improve legibility and credibility.

Your description doesn’t agree with that in the datasheet.